+86-20-3479-1069
Your present location:Home >> FAQ >> DIY pool safety cover installation instructions.How to install mesh safety cover for pool ?

DIY pool safety cover installation instructions.How to install mesh safety cover for pool ?

Writer:MeringSource:www.landy360.com Number of visits: Date:2018-05-11
 

DIY pool safety cover installation instructions.How to install mesh safety cover for pool ?

 

 

Pool safety cover installation manual 

TC safety pool covers are simply the best product to protect your family members.

 In order to install the cover quickly,please stick to the installation manual procedures below.

 


 

 

1.Please remove safety cover from bag and when you open the bag,you can see mesh safety 

pool cover accessories,installation tool and remove Tool.

Pool cover spring sleeves
Pool safety cover buckle
Brass pool safety cover anchors or threaded Anchors for above ground wood desk
Safety pool cover springs
⑤Tamping tool 
⑥Allen wrench 
⑦Pool safety cover bar

 

 

 

 2.Unfold the safety cover carefully on long side of pool and place the cover

 Carefully on pool.(Keeping water levels up,supports the cover during

 installation). 

 

3.Adjust the safety cover so that it overlaps the pool evenly on all sides and corners and

make sure they are even

 

 

 

4.Attaching pool cover straps with buckles and springs. 

5.Beginning with the center Straps of the length and width. Mark where

holes are to be drilled,approximately 20"from the pool cover edge.Once

 the anchor distance is confirmed, snap a chalk line along the width and length of the deck to

install anchors evenly and straight

6.Make holes on the ground for the pool cover anchors. 

 

 

 

 

 

7. After placed anchors on the ground by use a hammer,using the tension bar to pull the spring

away from the pool until the spring slides over the anchors make sure the spring is around 50% compressed. 

 

 

How to use Tension Bar? 

 

 

 

8.Install the safety cover spring to the anchors in below sequence to make sure the safety pool cover is properly placed. 

 

9.When removing a safety cover,insert the safety cover removal tool between the spring and the anchor.Lower all anchors .

 

so not to drag cover over raised anchors(if not,this may cause unwanted rips and tears in the cover.)Tip the rod towards the

cover to slip the ring of the anchors screw.Carefully pull the cover off the pool,clean it,place it in bag and in dry place for storage. 

 

 

10. TIPS: 
1.The water level of the pool must not be more than 18"below the solar cover and check the water level regularly. 


2.Concrete decks should be a minimum of 3 inches to 4 inches deep to ensure that anchors are secured. 


3.For mesh above ground pool covers wood decks,using our wood deck brass anchors and drill a hole with 1 1/2"diameter to a depth of 1/8". 
Then drill 3/4"diameter holes at least 2"deep,or through the deck,in the center of the original 1 1/2"holes. Drop the wood deck anchors into the

holes and Screw the anchors to the deck. 


4.To prevent damage to the cover,do not drag it.The labels should face up and all of the strap reinforcements should be facing down. 


5.If your safety mesh pool cover has any areas with cut-outs or zero tolerance areas (e.g.walls,waterfalls or elevated spas),install 
these areas first.If there are several areas like this,start at most complicated. 

 

Hope this safety pool cover installation guide can helps.If u want to know more about the installation detail,please feel free to contact us.

DIY pool safety cover installation instructions.How to install mesh safety cover for pool ?

 

 

lls,waterfalls or elevated spas),install 

these areas first.If there are several areas like this,start at most complicated. 

 

Hope this safety pool cover installation guide can helps.If u want to know more about the installation detail,please feel free to contact us.